Vectra is a line of desktop PC’s by HP that are targeted towards the business/Home Office segment, like the Dell OptiPlex or the Compaq Deskpro series of computers. Typically come with Intel Celeron/Pentium processors and onboard video.
The VEi8 can feature a Pentium II running at 350/400MHz or a Pentium III at 450/500MHz. with a Intel 440ZX chipset. Onboard video is the Matrox Millennium G200 with 8MB of graphics memory, which 86Box does not yet emulate
We have the option of restoring either a Windows 95 or Windows 98 image.
Windows 95 didn’t go as planned as we encountered a protection error upon boot up. At first I though the CPU used was too fast for Windows 95 as early builds had issues with CPU’s over a certain speed due to a race condition that’s executed upon boot up. A patch is available but you need to be in the Windows environment in order to install it. Downgrading the CPU and its speed had no effect in 86box.
Sadly I wasn’t able to fix this, and went for the Windows 98 option instead.
There isn’t much to see here, since its pretty close to a vanilla Windows install compared to the Compaq Presario, just a few HP utilities. I guess the Vecta line were intended to be used in business and office environment who would prefer to control and maintain the software that they would install.
Upon the first reboot a tutorial is run which gives a basic demonstration on how to use a computer. This looks like some sort of Windows 3.1 environment and only appears once.
Looks to be a hardware diagnostic application that shows detailed information on your system.
McAfee Antivirus and crash monitor are preinstalled by default and provide basic protection.
The real motherboard supports two floppy disks, and four IDE devices across two channels. Additional drives can be added by installing a SCSI adaptor in 86Box. Here I was using the Tekram DC-390 which Windows 98 detected as a AMD PCI SCSI controller automatically and installed a driver for it.
This wasn’t 100% perfect as adding a hard disk or a writable ZIP or Magneto optical disk would cause a blue screen upon boot up. Since we want to attach a writable drive to the computer, this was far from ideal.
I tried installing a driver I found online but it had no effect, there is an issue when using this adaptor in 86Box. I switched it out for another PCI SCSI card, Buslogic but it had the same issue with a BSOD upon boot up when a writable drive is attached.
Couldn’t find anything online relating to the BSOD above, any results turn up of that video of Windows 98 crashing in front of Bill Gates after plugging in a scanner.
In the end I tried to use another SCSI card instead, this time a ISA based card which required me to disable PCI IRQ steering for IRQ 10 & 11 to free up an IRQ slot for both the SCSI and the sound card.
Which made no difference, it still BSOD upon boot up.
I even mounted the image as write protected but it made little to no difference.
The rest of the devices (Zip 250/CD-ROM drives) worked fine, just hard disks and the magneto optical drives caused the BSOD.
I did notice an odd issue when I added the slave IDE hard drive, where Windows would BSOD with an error about drive D: which it would have been mounted as. Booting from the Windows 95 start disk and formatting as FAT32 seemed to fix it as after booting up the system was fine, and the new volume was detected and mounted in My Computer.
My guess is HP are using some unorthodox driver that interfacing when another volume or partition is added.
For networking the Realtek RTL8029 was used, which Windows 98 has built in drivers for.
3D acceleration is possible by adding a 3DFX Voodoo card, which Windows 98 will also have a driver for but you will be better off installing an updated driver instead.
In terms of expansion, the motherboard itself has 3 ISA and 3 PCI slots
- ISA: BusLogic BT-545S, IRQ: 10, 0x334 DMA 7
- ISA: Realtek RTL8029AS
- ISA: Crystal CS4236B
- PCI: S3 Trio64V+
- PCI: 3DFX Voodoo graphics accelerator